Multi-Cure® 9001-E-v3.1 encapsulant cures in seconds to enhance moisture, thermal cycle, and abrasion resistance of electronic and microelectronic assemblies. This material offers adhesion to various component substrates. This encapsulant provides optimal coverage over difficult circuit geometries. 9001-E-v3.1 encapsulating material has high ionic purity, is solvent free, and isocyanate free. This encapsulant has been engineered to have a low modulus and low Tg to minimize stress on delicate wire bonds. Material exposed to light will cure in seconds, while any shadowed areas will cure upon heat exposure. 9001-E-v3.1 Visible/UV light-curable encapsulant is formulated for fast on-demand cure with the Dymax BlueWave® LED Prime UVA spot curing lamp and BlueWave® LED DX-1000 curing system.
Multi-Cure® 9001-E-v3.1 encapsulant is especially well suited for chip-on-board, chip-on-flex, multi-chip modules and wire bonding.
|9001-E-v3.1 Product Data Sheet||Request SDS|
Dymax materials are solvent free and cure upon exposure to light. Their ability to cure in seconds results in lower processing costs. When cured with Dymax UV light curing spot lamps, focused beam lamps, flood lamps, or conveyor systems they deliver optimum speed and performance for maximum efficiency. Dymax lamps offer the optimum balance of UV and visible light for the fastest, deepest cures. This product is in full compliance with the RoHS Directives 2002/95/EC and 2003/11EC.
Cured Appearance: Clear
Substrates: Ceramic; Leadframe; PCB; Flex; Silicon
Package Sizes Available*:
10 mL Syringe (MR)
30 mL Syringe (MR)
160 mL Cartridge
300 mL Cartridge
550 mL Cartridge
*In Europe materials are sold in g/kg not mL/L
Bare die encapsulation
UV/Visible light cure for fastest processing
Secondary heat cure for shadowed areas
One part, no mixing is required
Solvent free, Isocyanate free
Low Tg, low modulus for wire bonding
Compare Dymax UV/Visible Light-Curing Spot Lamps
Dymax spot-curing systems provide very high intensity (3,000-8,000 mW/cm2 (320-395 nm)) over a small area (typically <½", 5 mm diameter). These intensities usually result in a 0.5-5 second cure time. Dymax spot-curing systems utilize an integral timed/manual shutter and typically require little external shielding. An intensity adjustment feature aids users in both validating and controlling a UV light-curing process.
Spot lamp systems are ideal for curing small areas quickly and can be easily integrated into an automated assembly process or used as a turnkey bench-top system.
2 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 radiometer (320-395 nm)
3 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 LED radiometer
Compare Dymax UV/Visible Light-Curing Flood Lamps
Dymax UV light-curing flood-lamp systems offer moderate to high intensity (75-225 mW/cm2) over a large area (5" x 5" or 8" x 8" (127 mm x 127 mm or 203 mm x 203 mm)). These lamps are ideal for curing areas larger than ½" (12.7 mm) in diameter or curing many small parts simultaneously.
Dymax UV light-curing flood-lamp systems can be incorporated into conveyors, automated assembly systems, or used as turnkey bench-top units.
1 Intensity readings vary widely depending on the make and model of the radiometer. These intensities were measured with the ACCU-CAL™ 50 radiometer.
Compare Dymax UV/Visible Light-Curing Conveyor Systems
Dymax conveyors incorporate either flood or focused-beam curing systems. The benefits of light-curing conveyors include consistent cure times and the ability to cure larger parts. Another benefit of conveyors is that they completely shield operators from UV light. Dymax conveyors have 12" wide belts, and can be configured for 6" and 12" width curing. Conveyor speed is tightly controlled and typically ranges from 1-27.5 feet per minute (although faster conveyors are available). Dymax light-curing conveyors can be outfitted with different types of lamps and up to four lamps on a single conveyor.
1These conveyors require 120 volts. 230 volt conveyors are also available.