Dymax 501-E-REV-A adhesive activator, when pre-applied to metallic, plated, ceramic, or glass substrates including PCBs, rapidly cures high-strength Dymax Multi-Cure® 600 series and 800 series structural adhesives and 9- series thermal interface adhesives in gaps from less than 1 mil to 20 mils. 501-E-REV-A activator is environmentally safe because it is free of solvents. Activator bonding increases efficiency, consistency, and reliability. Activator 501-E-REV-A provides broad tolerance of adhesive-to-activator ratios. Rapid, on-demand curing to fixture or handling strength allows in-line quality control and increased production throughput.
» Read more on complimentary products to the 501-E-REV-A Adhesive Activator:
|501-E-REV-A Product Data Sheet||Request SDS|
Activator 501-E-REV-A is environmentally safe because it is completely free of solvents (VOCs) and ozone depleting chemicals (ODCs). Activator 501-E-REV-A's low volatility and high flash point also enhances safety in the workplace. This product is in full compliance with the RoHS2 Directives 2015/863/EU and 2011/65/EU.
Flash Point (Closed Cup): 245°F
Specific Gravity: 1.0
Package Sizes Available*:
8.3 mL Vial
8 Ounce Can
1 Quart Can
1 Gallon Can
5 Gallon Can
Used with Dymax structural bonding adhesives for increasing bond strength to metal, plated metal, ceramic, and glass substrates
Used to cure Dymax Multi-Cure® thermally conductive adhesive in shadowed areas beneath heat sinks
Strong structural bonds
Fixtures in seconds
No solvent flash-off time
No VOCs and ODCs
Compare Dymax UV/Visible Light-Curing Spot Lamps
Dymax spot-curing systems provide very high intensity (3,000-8,000 mW/cm2 (320-395 nm)) over a small area (typically <½", 5 mm diameter). These intensities usually result in a 0.5-5 second cure time. Dymax spot-curing systems utilize an integral timed/manual shutter and typically require little external shielding. An intensity adjustment feature aids users in both validating and controlling a UV light-curing process.
Spot lamp systems are ideal for curing small areas quickly and can be easily integrated into an automated assembly process or used as a turnkey bench-top system.
2 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 radiometer (320-395 nm)
3 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 LED radiometer
Compare Dymax UV/Visible Light-Curing Flood Lamps
Dymax UV light-curing flood-lamp systems offer moderate to high intensity (75-225 mW/cm2) over a large area (5" x 5" or 8" x 8" (127 mm x 127 mm or 203 mm x 203 mm)). These lamps are ideal for curing areas larger than ½" (12.7 mm) in diameter or curing many small parts simultaneously.
Dymax UV light-curing flood-lamp systems can be incorporated into conveyors, automated assembly systems, or used as turnkey bench-top units.
1 Intensity readings vary widely depending on the make and model of the radiometer. These intensities were measured with the ACCU-CAL™ 50 radiometer.
Compare Dymax UV/Visible Light-Curing Conveyor Systems
Dymax conveyors incorporate either flood or focused-beam curing systems. The benefits of light-curing conveyors include consistent cure times and the ability to cure larger parts. Another benefit of conveyors is that they completely shield operators from UV light. Dymax conveyors have 12" wide belts, and can be configured for 6" and 12" width curing. Conveyor speed is tightly controlled and typically ranges from 1-27.5 feet per minute (although faster conveyors are available). Dymax light-curing conveyors can be outfitted with different types of lamps and up to four lamps on a single conveyor.
1These conveyors require 120 volts. 230 volt conveyors are also available.