Multi-Cure® Adhesive for Metal, Glass, and Plastics
Multi-Cure® 6-625-SV01-REV-A adhesive is a flexible and resilient UV/Visible curing adhesive. These characteristics allow the bonds to withstand strains caused by different coefficients of expansion present when bonding dissimilar substrates. Multi-Cure 6-625-SV01-REV-A adhesive cures upon exposure to light and is designed for rapid assembling of parts made of metal, glass, ceramic, phenolic, filled polyamide, and other materials. This material is specially formulated to cure with heat in applications where shadowed areas exist. Typical applications include bonding automotive metal latches to windows and bonding CR-39 plastic lenses to eyeglass frames. Multi-Cure 6-625-SV01-REV-A adhesive has good adhesion to many metals, glass, ceramic, and thermoset plastics. Multi-Cure products can be cured with UV/Visible light, heat, or pre-applied activator.
|6-625-SV01-REV-A Product Data Sheet||Request MSDS|
Dymax materials are solvent free and cure upon exposure to light. Their ability to cure in seconds results in lower processing costs. When cured with Dymax UV light curing spot lamps, focused beam lamps, flood lamps, or conveyor systems they deliver optimum speed and performance for maximum efficiency. Dymax lamps offer the optimum balance of UV and visible light for the fastest, deepest cures. This product is in full compliance with the RoHS Directives 2002/95/EC and 2003/11EC.
Tensile at Break: 3,400 psi (23 MPa)
Glass; Metals; Ceramic; Thermoset plastics
Package Sizes Available*:
10 mL Syringe (MR)
30 mL Syringe (MR)
160 mL Cartridge
1 Liter WM Bottle
15 Liter Tapered Pail
*In Europe materials are sold in g/kg not mL/L
Glass fixtures and furniture
UV/Visible light curing
Secondary heat cure
Bonds withstand strains caused by different coefficients of expansion
Compare Dymax UV/Visible Light-Curing Spot Lamps
Dymax spot-curing systems provide very high intensity (3,000-8,000 mW/cm2 (320-395 nm)) over a small area (typically <½", 5 mm diameter). These intensities usually result in a 0.5-5 second cure time. Dymax spot-curing systems utilize an integral timed/manual shutter and typically require little external shielding. An intensity adjustment feature aids users in both validating and controlling a UV light-curing process.
Spot lamp systems are ideal for curing small areas quickly and can be easily integrated into an automated assembly process or used as a turnkey bench-top system.
2 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 radiometer (320-395 nm)
3 As measured through a 5-mm liquid lightguide with a Dymax ACCU-CAL™ 50 LED radiometer
Compare Dymax UV/Visible Light-Curing Flood Lamps
Dymax UV light-curing flood-lamp systems offer moderate to high intensity (75-225 mW/cm2) over a large area (5" x 5" or 8" x 8" (127 mm x 127 mm or 203 mm x 203 mm)). These lamps are ideal for curing areas larger than ½" (12.7 mm) in diameter or curing many small parts simultaneously.
Dymax UV light-curing flood-lamp systems can be incorporated into conveyors, automated assembly systems, or used as turnkey bench-top units.
1 Intensity readings vary widely depending on the make and model of the radiometer. These intensities were measured with the ACCU-CAL™ 50 radiometer.
Compare Dymax UV/Visible Light-Curing Conveyor Systems
Dymax conveyors incorporate either flood or focused-beam curing systems. The benefits of light-curing conveyors include consistent cure times and the ability to cure larger parts. Another benefit of conveyors is that they completely shield operators from UV light. Dymax conveyors have 12" wide belts, and can be configured for 6" and 12" width curing. Conveyor speed is tightly controlled and typically ranges from 1-27.5 feet per minute (although faster conveyors are available). Dymax light-curing conveyors can be outfitted with different types of lamps and up to four lamps on a single conveyor.
1These conveyors require 120 volts. 230 volt conveyors are also available.